Paving Contractors in West Virginia

How to make a walkway with paving stones?

Assuming you would like tips on how to lay a walkway with paving stones in West Virginia, USA: The first step is to plan the walkway. You will need to determine the size, shape, and location of the walkway. Once you have a plan, you will need to mark the area where the walkway will go. Next, you will need to excavate the area for the walkway. You will need to dig down about 6 inches (15 cm) so that the pavers will sit about 3 inches (7.5 cm) above the ground. Once the area is excavated, you will need to add a layer of gravel. This will help with drainage and will provide a base for the pavers. Now you are ready to start laying the pavers. Begin at one end of the walkway and work your way to the other. It is important to make sure that the pavers are level and that there is a consistent space between each paver. Once all of the pavers are in place, you will need to fill the spaces between the pavers with sand. This will help to keep the pavers in place and will give the walkway a finished look.

How to clean limestone paving?

Assuming you are asking how to clean dirt and stains off of limestone paving, here are some instructions: First, sweep the surface of the paving to remove any loose dirt or debris. Next, mix up a solution of mild dish soap and water. Apply the soap solution to the paving using a sponge or brush, and scrub gently to remove any remaining dirt or stains. Rinse the paving with clean water to remove any soap residue. If necessary, repeat the process until the paving is clean.

How much does block paving cost per square metre?

The cost of block paving will vary depending on the location, type of block paving, and the company you purchase it from. In West Virginia, the average cost of block paving is $12 per square metre. However, this can range from $10-$15 per square metre, depending on the type of block paving and the company you purchase it from.

Is a paved driveway cheaper than concrete?

Is a gravel driveway cheaper than concrete? Yes, in most cases. gravel is cheaper to install than concrete. Concrete costs money. On top of that, concrete is strong and a great material for a driveway.

Is asphalt the same as blacktop?

Blacktop is a surface made of gravel and clay mixed with fine bituminous coal. Asphalt is a mixture of sand, clay, and mineral fibers, with a tiny bit of bitumen mixed in. Blacktop is more porous and absorbs more moisture, which can cause uneven heating and can cause premature wear on vehicles.

How to lay paving bricks?

Assuming you would like tips for laying paving bricks in West Virginia, USA: 1. Begin by planning your design and measuring the area you will be covering. It is important to allow for proper drainage, so be sure to slope the paving area away from any buildings or other structures. 2. Next, prepare the area by removing any existing grass or other vegetation. You will also need to excavate the area to a depth of at least 4 inches. Be sure to compact the soil before proceeding. 3. Once the area is prepared, you can begin laying your bricks. Start by spreading a layer of sand over the entire area. This will help to level the surface and provide a bed for the bricks to rest on. 4. To lay the bricks, start at one corner and work your way outward. Be sure to use a level to ensure that each row of bricks is level with the others. You can use a brick trowel to spread mortar between the bricks, or you can use a pre-mixed adhesive. 5. After the bricks are in place, you can fill any joints with mortar or adhesive. You can also use sand to fill any joints that are 1/8 inch or wider. 6. Finally, sweep any excess sand or debris from the surface of the paving and allow the area to cure for at least 24 hours before walking or driving on it.

How much does a paving company make?

Assuming you are asking for an estimate of revenue: A paving company in West Virginia might make anywhere from a few hundred dollars to several thousand dollars in a given year. This estimate depends on a number of factors, including the size of the company, the number of projects they take on, the location of their projects, and the going rate for paving services in the area. Generally speaking, a paving company will make more money if they are located in a busy urban area with a high demand for their services. They will also make more money if they are able to take on a large number of projects.

What is the cheapest way to pave?

Asphalt is the cheapest way to pave a driveway. Asphalt provides a smooth, stable surface and holds up well in direct sunlight. It can be somewhat cold to the touch in the winter and can easily heat up in the summer.

How much does it cost to hot top a driveway?

Typically, the cost of hot paving costs between $1.50 and $3.50 per square foot, or between $150 and $350 to pave a 24-inch-wide driveway of about 20 feet in length. The amount of paving needed will affect the final price. If you plan on paving a large driveway, expect to pay more.