Find The Best Deals For

Paving Contractors in Kentucky

SpotDif is a market comparison site that helps you find the best paving contractor in Kentucky. We provide you with a list of paving contractors in your area so that you can compare their services and prices. If you’re looking for paving contractors in Kentucky, you may have a difficult time finding the right ...Read more

red motor scooter parked beside green plants

Let’s find the right deal for you

We compare deals from all the major providers across the UK to find you the best possible deal. Simply answer a few questions to help us understand exactly what you’re looking for.

true Save your time by comparing quickly
true Save money by finding grants and deals
true Regularly updated for the latest offers

The latest news

Paving Contractors in Kentucky FAQs

How to lay paving slabs on sand?

There are a few things to keep in mind when laying paving slabs on sand. First, make sure the sand is firm and level. You don’t want any dips or bumps that could throw off the level of your paving slabs. Second, use a garden hose to wet the sand down before you start laying the slabs. This will help the slabs adhere to the sand better. Finally, start in one corner and work your way out, laying each slab as level as possible. Use a level to check as you go to make sure everything is staying level. If everything looks good, you’re all done!

How to clean cement off paving slabs?

Assuming you are referring to how to clean cement or mortar off of paving stones or slabs, below are a few ways to do so. If the cement or mortar is still wet, you can try using a putty knife or trowel to scrape it off. If it is already dry, you will need to use a stiff brush or wire brush to scrub it off. You may also need to use a power washer to remove any stubborn residue. If you are trying to remove cement or mortar from brick pavers, you can try using a chisel or hammer to break it off in small pieces. You may also need to use a power washer to remove any stubborn residue.

How long after paving can you drive on it?

After paving, you should wait at least 24 hours before driving on it.

Is a paved driveway cheaper than concrete?

As far as installation costs and concrete costs go, a poured-concrete driveway is technically the most expensive per square foot. However, concrete slabs actually cost less to install ; in fact, they’re so cost-effective that they represent a great value as far as materials and workmanship go.

Is asphalt the same as blacktop?

Blacktop is a hard, smooth, hot-color, asphalt-based paving surface. Gravel is a soft, coarse-grained, friable, non-porous paving material.

How to get rid of weeds in block paving?

Answer: To get rid of weeds in block paving, you will need to pull them up by hand or use a weed killer. If you have a pressure washer, you can also use it to remove weeds from cracks in the paving.

Explaining to contractor what you need for paving parking lot?

In order to pave a parking lot, you will need a contractor who is experienced in paving. You will also need to have the area cleared and graded, as well as any necessary drainage installed. The contractor will then need to install a base layer of asphalt or concrete, followed by a layer of pavement. Finally, the contractor will need to seal the pavement to protect it from the elements.

What is the cheapest way to pave?

As the least expensive paving material, gravel is the most common ground for other materials to be transported and placed on. Gravel is the second-cheapest paving material after sand.

How much does it cost to hot top a driveway?

A standard driveway installation costs $5 to $10 per square foot plus $0.05 to $0.10 per square foot for asphalt or $0.05 to $0.08 per square foot for concrete. The cost of hot-tapping a driveway is usually between $75 and $150, plus the cost of concrete or asphalt.

Basic information.

please complete the information below.

1 of 1 Done Check
One last thing!

Please agree to the below so we can get your results.

Our Feedback

Your SpotDif account