FEATURE YOUR BUSINESS ON SPOTDIF

Find The Best Deals For

Paving Contractors in Herefordshire

Paving contractors in Herefordshire, England, United Kingdom offer a wide variety of services to their clients. These services can include but are not limited to, the installation of new paving, the repair of existing paving, the removal of old paving, and the maintenance of paving. Paving contractors can be found in the Yellow Pages or online. ...Read more

Paving Contractors in Herefordshire

Let’s find the right deal for you

We compare deals from all the major providers across the UK to find you the best possible deal. Simply answer a few questions to help us understand exactly what you’re looking for.

true Save your time by comparing quickly
true Save money by finding grants and deals
true Regularly updated for the latest offers

The latest news

Paving Contractors in Herefordshire FAQs

How to mix mortar for paving?

There are a few things to consider when mixing mortar for paving, such as the type of mortar, the ratio of ingredients, and the amount of water needed. The type of mortar you’ll need depends on the type of paving you’re doing. For example, if you’re paving with concrete, you’ll need a different type of mortar than if you’re paving with brick. The ratio of ingredients is also important. You’ll need to use more cement if you’re paving in a cold climate, as the temperature can affect the setting time. Finally, you’ll need to add the right amount of water. Too much water will make the mortar too runny, while too little water will make it too dry. The best way to achieve the right consistency is to add a little water at a time and mix thoroughly until you reach the desired consistency.

How to lay paving stones?

To lay paving stones, you will need the following materials: -Paving stones -Sand -Gravel -Cement -Water First, you will need to clear the area where you will be laying the paving stones. Make sure the ground is level and free of any debris. Next, you will need to mark out the area where you will be laying the paving stones. You can do this by using string or chalk. Once you have marked out the area, you will need to dig a trench. The trench should be the same width as the paving stones and about 6 inches deep. After you have dug the trench, you will need to fill it with sand. Use a tamper to compact the sand. Next, you will need to lay the paving stones. Start by laying the first stone in the corner of the marked out area. Then, continue to lay the rest of the stones, working your way from the corner. Make sure that the stones are level as you lay them. Once all of the stones are in place, you will need to fill the joints between the stones with gravel. Finally, you will need to mix some cement with water to create a slurry. Use a brush to apply the slurry to the joints between the stones.

How to lay granite paving slabs?

Laying granite paving slabs can be a difficult and time-consuming task. However, with the proper preparation and tools, it can be done relatively easily. First, you will need to mark out the area where you will be laying the paving slabs. This can be done with string or chalk. Once the area is marked out, you will need to excavate the area to a depth of at least 6 inches. This will ensure that the granite paving slabs have a firm foundation to be laid on. Next, you will need to lay a layer of hardcore. This should be compacted firmly to create a stable base. Once the hardcore is in place, you will need to lay a layer of sand. This should be levelled off so that it is even with the top of the hardcore. Now, you are ready to start laying the granite paving slabs. Begin by laying the slabs around the edge of the area. Once the edge slabs are in place, you can start filling in the middle. It is important to make sure that the slabs are level with each other. Use a spirit level to check that they are even. Once all of the slabs are in place, you will need to fill the joints between them with mortar. Use a trowel to apply the mortar, and then use a brush to smooth it out. Leave the mortar to set for at least 24 hours before walking on the paving

How to apply block paving sealant?

Block paving sealant can be applied in a number of ways, but the most common method is to brush it on with a stiff bristled brush. It is important to ensure that the surface is clean and dry before application, as any dirt or moisture will prevent the sealant from bonding properly. Once the sealant has been applied, it is important to allow it to dry completely before walking or driving on the surface.

How many paving bricks in a square meter?

There is no definitive answer to this question as it will depend on the size of the paving bricks being used. However, a good rule of thumb is that there will be approximately 100 paving bricks in a square meter.

What sand for paving slabs?

There are a few things to consider when choosing sand for paving slabs. The first is the type of paving slab you are using. There are many different types of paving slabs, and each type has its own specific needs. For example, some paving slabs require a very fine sand, while others require a coarse sand. The second thing to consider is the climate. Herefordshire has a temperate climate, so a variety of sands will work well. However, if you are paving in an area with a hot climate, you will need to choose a sand that can withstand the heat. The third thing to consider is the amount of traffic the area will see. If the area is very busy, you will need to choose a sand that is very durable.

How to remove oil stains from block paving?

One way to remove oil stains from block paving is to use a product called ‘Oil Gone Easy’. This is a water-based solution that is sprayed onto the affected area. The oil is then absorbed by the solution, which can be removed with a pressure washer. Another way to remove oil stains from block paving is to use a product called ‘Oil Stain Remover’. This is a solvent-based solution that is applied to the affected area with a brush. The solvent dissolves the oil, which can then be removed with a pressure washer.

How many square meters in a pack of block paving?

A pack of block paving typically contains 50 square meters of paving.

How much to lay porcelain paving?

Assuming you are asking how much it would cost to have someone else lay porcelain paving for you in Herefordshire, UK, the answer would depend on a few factors. The size of the area you want paved, the type of porcelain paving you choose, and the company you hire to do the job would all affect the cost. To give you a rough idea, laying porcelain paving can cost anywhere from £50 to £100 per square metre. So, if you have a 20 square metre patio, you could be looking at a cost of £1,000 to £2,000. Of course, you could always lay the paving yourself to save on labour costs. However, this is a big job and is not recommended unless you are confident in your DIY skills. If you do decide to tackle it yourself, you will also need to factor in the cost of the paving, tools and any other materials you need.

Basic information.

please complete the information below.

1 of 1 Done Check
One last thing!

Please agree to the below so we can get your results.

Our Feedback

Your SpotDif account

Get in touch

Drop us a message below and one of our team will get back to you within 24 hours

Subject of enquiry